VGA display… On a 3″ scope tube!

Yes, you’ve all thrown away your lunky old CRT monitors, in favour of sleek ultra-thin LCD displays. And, you thought you’d never see another one again…

But this CRT display has a twist! It’s round. It’s small at just 3 inches diameter. And it’s awfully cute.

Oscilloclock 3-inch CRT VGA Display Assembly - overview

Last year, I was approached by a dedicated flight simulation enthusiast, who needed a radar indicator to use in a fighter cockpit replica. The indicator should employ a CRT, for the most realistic look. Could Oscilloclock design and construct such a display?

It didn’t take much convincing! Diverging only temporarily from building clocks, I took up the challenge to create my first raster-scan CRT display unit. In the ensuing months, difficulties sprang forth from every direction in the project, but ultimately I was able to avoid a diraster (sic) and deliver a functional assembly:

See more related videos on my YouTube channel

The Setup

The key component of this setup is a new prototype VGA Board that converts a VGA signal into analogue X and Y outputs. Both analogue intensity and binary blanking outputs are provided.

Oscilloclock VGA Board prototype

Oscilloclock VGA Board prototype

The X and Y outputs drive an Oscilloclock Deflection Board, while the binary blanking output drives the blanking amplifier in a CRT Board.

Oscilloclock Deflection Board - modified for ultra-linear HV output

Deflection Board – modified for ultra-linear HV output

CRT Board - heavily modified for improved frequency response

CRT Board – modified for improved frequency response

Blanking isolation, heater, and HV supplies are provided by a Power Board.

Power Board - with improved optocoupler

Power Board – with improved optocoupler

It all looks so easy! But noooo. Astute readers will recall from other posts that every Oscilloclock project involves sleepless slumbers, horrific hair-pulling, and forgotten family members. Let’s see what caused me grief this time…

Continue reading

Making the Heathkit Oscilloclock

Last month’s post about the Heathkit Oscilloclock generated tremendous interest, and I’ve heard from several folks keen to try their hand at preserving their own beloved instruments.

… so let’s take a brief look at what was involved in the Heathkit OR-1 conversion!

Heathkit Oscilloclock - inside

Approaches to conversion…

There are many approaches to retrofitting a scope into an Oscilloclock, but it really boils down to how much of the original circuit you want to re-use, vs. what you will bypass with Oscilloclock boards.

Continue reading

A Heathkit Oscilloclock!

Anyone familiar with Heathkit®?

From 1947 to 1992, the U.S. based Heath Company produced electronic kits for everything you can imagine: radios, TVs, computers, robots, ham gear, and electronic test equipment. Yes, you guessed it – they also produced kits for oscilloscopes!

My Grandpa purchased one such scope, the Heathkit OR-1, around 1960. He wanted to kick off a new career in electronics repair, and the ‘build-your-own-equipment’ approach to training was in full bloom at the time. Also, since this was before the era of cheap overseas manufacturing, he could buy a Heathkit far cheaper than an assembled scope.

Heathkit OR-1 manual - a work of art

Heathkit OR-1 manual – a work of art

Unfortunately, Grandpa’s electronics career never really took off. But decades later, he introduced me to his gorgeous oscilloscope, and boy – did that kick MY career off! Much later, the OR-1 came to live with me. (You can read a bit more about my affinity for this scope in my History page.)

The problem is, I have too many oscilloscopes. But I don’t have enough Oscilloclocks. What more fitting way to keep Grandpa’s legacy alive, than to retrofit his Heathkit?

Heathkit OR-1 Oscilloclock

Heathkit Oscilloclock - Splash and Clock

Special features

Continue reading

Oscilloclock.com site is open!

This site is dedicated to showcasing my Scope Clock designs, and to sharing technical information openly to anyone interested in these vintage electronic timepieces.

What is an “(Oscillo)scope Clock”?

A unique style of clock that displays the time (and other fun things) on a CRT taken from an old oscilloscope. These clocks operate on a fusion of old and new electronics, and are often housed in beautifully crafted cases of wood, metal, or acrylic.

Continue reading